T10 iin gps program

Show More. People also like. Upgrade WP Free. Windows Insider Free. Update Central Free. Firmware Update Check - Update assistant for legacy Win. WinDroid Lollipop Free. Xender Free. Additional information Published by Ananthan Unni. Published by Ananthan Unni.

Developed by Ananthan Unni. Approximate size 3. Age rating For all ages. This app can Use your location Access your Internet connection and act as a server. I tested my T10 head unit before swapping all of the OEM plastic parts. I simply plugged in all of the plastic plugs from the head unit to the truck, turned the ignition key and made sure it was getting power. It was, so I moved to the next step. These parts are a direct lift from the OEM unit shown above for reference.

There are clips and a few screws holding them in that will need to be handled carefully. You will install the plastic top tray from the OEM unit into the T10, as well as the two vents and two small plastic pieces that hold the air volume adjuster dials.

Take your time on the top tray and make sure you use the correct size of screwdriver so you do not damage the screw heads or the holes they go into. There are two sets of screws from the removal of the OEM head unit. Use the larger screws for the top tray. These screws were a bit stubborn, and I slightly stripped the heads as a result.

So, I drilled out the holes in the T10 very slightly and the screws went in easily. RH Vent goes right. LH vent goes left. Before we install the vents, you must install the small plastic outer air volume dial trims on either side of the face plate.

There is a right and left side. Use the smaller screws. Two on each side. These took a bit of finessing to get the small pegs into the holes and the screw holes lined up. Take your time and make sure these are fitted correctly before threading in the screws.

The vents install from the rear of the faceplate, and have clips on the top, bottom and sides. Just push until all of the clips click in. I had to use a small screwdriver to finesse a couple of them into place. I know, I keep saying this… I used one of the plastic tools provided and pried gently under the edges of each clip and pulled them off with my hand. There are a total of six. When you snap them onto the T10, yellows will go on top and bottom, and the white tabs go in the middle on each side.

Make sure you push them all the way on until they click into place. I scratched my OEM screen on the gear shift when I did a prior install. But, be careful not to put pressure on the screen regardless or it may crack. Put it into the SIM holder on the T I went ahead and installed this harness in case I want to use a SIM in the future.

Work from the truck to attach the harnesses. They all have different numbers of pins and sizes of plugs, so obviously plug the ends that fit into the ends that they fit into. This should be fairly self-explanatory. There are seven white plugs open on the wiring harness, and two will not attach to anything.

See photo below Just let those hang. I ran mine just below the left side of the glove box for now. I stuck mine just above the right air vent. Leave the 3G in the middle if you chose to use that cable. At this point, I turned on the ignition and did another test to make sure the T10 was getting power and it was.

So, I proceeded to close up the project. Tidy up the wires as much as you like and shove them into the cavity in the vehicle behind he head unit. Align the head unit so the six tabs go into their corresponding holes. Push the corners of the radio until it clicks into place. Next, install the air control knob assembly by first reconnecting the white clip and plug that you removed when we started. Then, simply push the control assembly straight forward until it clicks into place.

Set the side pieces in position and firmly push them onto the console with both hands until they click in place. Wipe off your console with a clean, dry, soft cloth preferably a computer screen or phone polishing cloth. When everything was all back together and I powered up the fully installed T10, it was a bit like the 4Runner came to life. With a few taps, my phone was connected wirelessly and playing music.

No problems at all. And the sound is noticeably better. If there is only mild and partial damage, the patient may only experience weakness, numbness, lack of muscle control, or loss of the use of only one side of their lower body. Complete damage to this vertebra in a worst-case scenario could result in the patient losing use of their lower body paraplegia.

The cervical spine consists of seven vertebrae and is located at the base of the skull. Its function is to support the skull, enabling head movements…. The thoracic spinal vertebrae consist of 12 total vertebrae and are located between the cervical vertebrae which begin at the base of the skull and…. An intervertebral disk acts as shock absorber between each of the vertebrae in the spinal column by keeping the vertebrae separated when there is…. The vertebral column, also known as the spinal column, is a flexible column that encloses the spinal cord and also supports the head.

It consists of…. The T12 vertebra is the twelfth thoracic vertebra in the spine of the human body. It is part of the spinal column, which supports the top of the human…. The human backbone is a column of 33 total vertebrae, of which 24 are movable and free the remainder are fused.